APRS Track Direct

My position About ☰

reset

TA8MRM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA8MRM-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RSSI*	Voltage*
1732211861	18 Pkt	31 dBm	12.1 V
1732210908	16 Pkt	31 dBm	12.1 V
1732209955	16 Pkt	31 dBm	12.1 V
1732209005	17 Pkt	31 dBm	12.12 V
1732208054	16 Pkt	31 dBm	12.12 V
1732207096	20 Pkt	31 dBm	12.1 V
1732206145	26 Pkt	31 dBm	12.1 V
1732205191	19 Pkt	31 dBm	12.12 V
1732204236	19 Pkt	31 dBm	12.12 V
1732203278	24 Pkt	31 dBm	12.1 V
1732202327	19 Pkt	31 dBm	12.12 V
1732201374	19 Pkt	31 dBm	12.1 V
1732200424	6 Pkt	31 dBm	12.1 V
1732199474	6 Pkt	31 dBm	12.1 V
1732198523	8 Pkt	31 dBm	12.1 V
1732197565	9 Pkt	31 dBm	12.1 V
1732196615	7 Pkt	31 dBm	12.1 V
1732195663	8 Pkt	31 dBm	12.1 V
1732194704	7 Pkt	31 dBm	12.1 V
1732193746	10 Pkt	31 dBm	12.1 V
1732192794	8 Pkt	31 dBm	12.1 V
1732191835	5 Pkt	31 dBm	12.1 V
1732190875	9 Pkt	31 dBm	12.12 V
1732189917	8 Pkt	31 dBm	12.1 V
1732188962	5 Pkt	31 dBm	12.12 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)