APRS Track Direct

My position About ☰

reset

NO2C-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object NO2C-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	Temp*
1753651568	208 Pkts	196 Pkts	48 C
1753647968	214 Pkts	202 Pkts	48 C
1753644368	191 Pkts	181 Pkts	48 C
1753640768	145 Pkts	137 Pkts	48 C
1753637168	226 Pkts	211 Pkts	49 C
1753633568	199 Pkts	188 Pkts	49 C
1753629968	194 Pkts	186 Pkts	49 C
1753626368	214 Pkts	205 Pkts	49 C
1753622768	208 Pkts	204 Pkts	47 C
1753619168	222 Pkts	209 Pkts	47 C
1753615568	291 Pkts	277 Pkts	49 C
1753611968	299 Pkts	286 Pkts	49 C
1753608368	298 Pkts	282 Pkts	47 C
1753604768	369 Pkts	351 Pkts	49 C
1753601168	323 Pkts	307 Pkts	49 C
1753597568	346 Pkts	331 Pkts	47 C
1753593968	280 Pkts	264 Pkts	49 C
1753590368	267 Pkts	256 Pkts	49 C
1753586768	186 Pkts	182 Pkts	49 C
1753583168	138 Pkts	136 Pkts	49 C
1753579568	92 Pkts	89 Pkts	49 C
1753575968	112 Pkts	110 Pkts	48 C
1753572368	191 Pkts	185 Pkts	48 C
1753568768	216 Pkts	206 Pkts	48 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)