APRS Track Direct

My position About ☰

reset

K4ROM-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K4ROM-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	BattV*	SolarV*	chgWhToday*
1762340435	51.02 V	0.24 V	0 Wh
1762338635	51.06 V	0.11 V	0 Wh
1762336836	51.09 V	0.15 V	0 Wh
1762335035	51.13 V	0.23 V	0 Wh
1762333235	51.18 V	0.35 V	0 Wh
1762331434	51.21 V	0.32 V	0 Wh
1762329635	51.25 V	0.42 V	0 Wh
1762327834	51.26 V	0.4 V	0 Wh
1762326034	51.29 V	0.32 V	0 Wh
1762324234	51.32 V	0.65 V	0 Wh
1762322434	51.35 V	0.68 V	0 Wh
1762320634	51.37 V	0.71 V	0 Wh
1762318834	51.39 V	0.71 V	0 Wh
1762317034	51.42 V	0.71 V	0 Wh
1762315233	51.43 V	0.7 V	0 Wh
1762313433	51.45 V	0.66 V	700 Wh
1762311633	51.47 V	0.64 V	700 Wh
1762309833	51.48 V	0.59 V	700 Wh
1762308032	51.5 V	0.55 V	700 Wh
1762306232	51.51 V	0.48 V	700 Wh
1762304433	51.51 V	0.43 V	700 Wh
1762302632	51.51 V	0.36 V	700 Wh
1762300832	51.54 V	0.29 V	700 Wh
1762299032	51.56 V	0.2 V	700 Wh
1762297232	51.61 V	1.08 V	700 Wh

*Used Equation Coefficients:

BattV: 0, 1, 0

BattC: 0, 1, 0

SolarV: 0, 1, 0

SolarC: 0, 1, 0

chgWhToday: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)