APRS Track Direct

My position About ☰

reset

ZL1AOR-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ZL1AOR-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1836274509	13.5 Volt	240 Pkt	70 Pkt	71 Pcnt
1836274360	13.73 Volt	250 Pkt	80 Pkt	67 Pcnt
1836273911	14.25 Volt	230 Pkt	70 Pkt	73 Pcnt
1774121306	12.75 Volt	270 Pkt	80 Pkt	49 Pcnt
1774120705	12.75 Volt	260 Pkt	80 Pkt	47 Pcnt
1774120110	12.75 Volt	250 Pkt	80 Pkt	48 Pcnt
1774119504	12.75 Volt	240 Pkt	80 Pkt	48 Pcnt
1774118904	12.75 Volt	240 Pkt	80 Pkt	48 Pcnt
1774118309	12.75 Volt	240 Pkt	80 Pkt	47 Pcnt
1774117703	12.75 Volt	230 Pkt	80 Pkt	47 Pcnt
1774117102	12.75 Volt	230 Pkt	80 Pkt	49 Pcnt
1774116507	12.75 Volt	230 Pkt	80 Pkt	47 Pcnt
1774115901	12.75 Volt	220 Pkt	70 Pkt	46 Pcnt
1774115303	12.75 Volt	230 Pkt	80 Pkt	46 Pcnt
1774114702	12.75 Volt	240 Pkt	80 Pkt	47 Pcnt
1774114099	12.75 Volt	240 Pkt	80 Pkt	46 Pcnt
1774113499	12.75 Volt	250 Pkt	80 Pkt	46 Pcnt
1774112904	12.75 Volt	240 Pkt	80 Pkt	45 Pcnt
1774112298	12.75 Volt	240 Pkt	80 Pkt	44 Pcnt
1774111697	12.75 Volt	240 Pkt	80 Pkt	44 Pcnt
1774111099	12.75 Volt	240 Pkt	80 Pkt	43 Pcnt
1774110496	12.83 Volt	240 Pkt	80 Pkt	44 Pcnt
1774109895	12.83 Volt	250 Pkt	80 Pkt	45 Pcnt
1774109300	12.75 Volt	270 Pkt	80 Pkt	48 Pcnt
1774108694	12.83 Volt	260 Pkt	80 Pkt	48 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, -0.3

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)