APRS Track Direct

My position About ☰

reset

BV4HW-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV4HW-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1836274544	34.5 C	16 p	24 p	69 p	62 p
1836274094	33.2 C	4 p	16 p	53 p	47 p
1762266428	38.2 C	6 p	13 p	227 p	223 p
1762265227	37.8 C	4 p	40 p	221 p	217 p
1762264027	37.4 C	5 p	46 p	219 p	215 p
1762262828	35.1 C	20 p	48 p	214 p	210 p
1762260427	37.3 C	8 p	8 p	174 p	170 p
1762259227	36.7 C	1 p	2 p	167 p	163 p
1762258027	37.1 C	1 p	5 p	166 p	162 p
1762256828	36.7 C	1 p	5 p	166 p	162 p
1762255627	36.3 C	4 p	7 p	165 p	161 p
1762254427	36.2 C	4 p	7 p	165 p	161 p
1762253228	36.5 C	3 p	5 p	163 p	159 p
1762252028	36.5 C	1 p	3 p	160 p	156 p
1762250828	36.6 C	1 p	4 p	159 p	155 p
1762249627	36.8 C	1 p	3 p	158 p	154 p
1762248429	34.3 C	2 p	2 p	157 p	153 p
1762247227	34.9 C	8 p	26 p	155 p	152 p
1762246028	33.6 C	8 p	26 p	155 p	152 p
1762244827	34 C	8 p	26 p	155 p	152 p
1762243627	36.7 C	8 p	26 p	155 p	152 p
1762242428	38 C	10 p	24 p	152 p	149 p
1762241228	39.1 C	13 p	15 p	142 p	139 p
1762240028	39.5 C	2 p	10 p	129 p	126 p
1762238827	36.3 C	1 p	9 p	128 p	125 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)