APRS Track Direct

My position About ☰

reset

VK5RWR-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK5RWR-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1786731291	12.27 Volt	150 Pkt	68 Pcnt	12.5 C
1786730391	12.27 Volt	150 Pkt	71 Pcnt	12.5 C
1786729491	12.27 Volt	160 Pkt	74 Pcnt	12.5 C
1786728591	12.27 Volt	160 Pkt	78 Pcnt	12.5 C
1786727691	12.27 Volt	170 Pkt	80 Pcnt	12.5 C
1786726791	12.27 Volt	170 Pkt	81 Pcnt	12.5 C
1786725891	12.27 Volt	180 Pkt	81 Pcnt	12.5 C
1786724991	12.27 Volt	170 Pkt	82 Pcnt	12.5 C
1786724091	12.27 Volt	160 Pkt	81 Pcnt	12.5 C
1786723191	12.27 Volt	130 Pkt	82 Pcnt	12.5 C
1786722291	12.27 Volt	110 Pkt	82 Pcnt	13 C
1786721391	12.27 Volt	100 Pkt	81 Pcnt	13 C
1786720491	12.27 Volt	90 Pkt	81 Pcnt	13.5 C
1786719593	12.27 Volt	100 Pkt	78 Pcnt	13 C
1786718691	12.27 Volt	110 Pkt	76 Pcnt	13 C
1786717791	12.27 Volt	120 Pkt	80 Pcnt	12.5 C
1786716892	12.27 Volt	130 Pkt	83 Pcnt	12.5 C
1786715992	12.27 Volt	130 Pkt	86 Pcnt	13 C
1786715092	12.27 Volt	140 Pkt	89 Pcnt	13 C
1786714192	12.27 Volt	140 Pkt	91 Pcnt	13 C
1786713292	12.27 Volt	140 Pkt	89 Pcnt	13 C
1786712392	12.27 Volt	140 Pkt	90 Pcnt	13.5 C
1786711492	12.27 Volt	150 Pkt	92 Pcnt	13.5 C
1786710592	12.27 Volt	140 Pkt	89 Pcnt	13.5 C
1786709692	12.27 Volt	140 Pkt	90 Pcnt	14 C

*Used Equation Coefficients:

Vin: 0, 0.073, 0.01

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)