APRS Track Direct

My position About ☰

reset

LU5RNS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU5RNS-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1752861399	7 Pkt	-45 dBm	13.13 V
1752860475	9 Pkt	-45 dBm	13.1 V
1752859551	19 Pkt	-42 dBm	13.13 V
1752858628	11 Pkt	-39 dBm	13.13 V
1752857705	19 Pkt	-43 dBm	13.1 V
1752856781	20 Pkt	-40 dBm	13.1 V
1752855857	16 Pkt	-37 dBm	13.1 V
1752854933	15 Pkt	-40 dBm	13.1 V
1752854010	22 Pkt	-46 dBm	13.1 V
1752853086	12 Pkt	-47 dBm	13.13 V
1752852163	18 Pkt	-41 dBm	13.1 V
1752851239	14 Pkt	-39 dBm	13.13 V
1752850317	16 Pkt	-47 dBm	13.1 V
1752849393	13 Pkt	-50 dBm	13.13 V
1752848469	20 Pkt	-47 dBm	13.13 V
1752847546	16 Pkt	-47 dBm	13.13 V
1752846621	19 Pkt	-50 dBm	13.13 V
1752845698	13 Pkt	-48 dBm	13.13 V
1752844774	27 Pkt	-48 dBm	13.13 V
1752843850	9 Pkt	-47 dBm	13.13 V
1752842927	15 Pkt	-48 dBm	13.13 V
1752842003	18 Pkt	-47 dBm	13.13 V
1752841079	21 Pkt	-52 dBm	13.13 V
1752840155	13 Pkt	-43 dBm	13.13 V
1752839234	27 Pkt	-48 dBm	13.13 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)