APRS Track Direct

My position About ☰

reset

BM1CKC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM1CKC-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790668615	43 C	28 p	96 p	3798 p
1790667416	41.9 C	34 p	115 p	3872 p
1790666218	42.8 C	34 p	147 p	3934 p
1790665017	42.8 C	47 p	185 p	4000 p
1790663815	42.5 C	66 p	225 p	4064 p
1790662616	41.3 C	72 p	214 p	4118 p
1790661412	42.4 C	87 p	190 p	4137 p
1790660212	41.3 C	55 p	149 p	4116 p
1790659009	40.9 C	47 p	139 p	4137 p
1790657809	42 C	46 p	135 p	4166 p
1790656608	41.5 C	45 p	126 p	4218 p
1790655406	41.5 C	44 p	137 p	4241 p
1790654209	42 C	37 p	168 p	4256 p
1790653010	40.2 C	56 p	167 p	4292 p
1790651805	41.3 C	75 p	158 p	4295 p
1790650606	41.3 C	36 p	133 p	4275 p
1790649407	40.3 C	47 p	142 p	4299 p
1790648196	40.8 C	50 p	162 p	4315 p
1790646994	40.7 C	45 p	163 p	4325 p
1790645799	39.9 C	67 p	187 p	4342 p
1790644598	40.8 C	51 p	184 p	4329 p
1790643391	40.1 C	69 p	184 p	4337 p
1790642201	39 C	64 p	158 p	4321 p
1790641001	38.8 C	51 p	146 p	4317 p
1790639822	37.7 C	43 p	140 p	4316 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)