APRS Track Direct

My position About ☰

reset

KC3ARY Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC3ARY. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Battery Voltage*	Battery Current*	Load Current*	Solar Voltage*
1744950017	12.69 V	279 mA	-254 mA	0 V
1744949417	12.69 V	272 mA	-246 mA	0 V
1744948817	12.7 V	277 mA	-251 mA	0.01 V
1744948217	12.7 V	280 mA	-254 mA	0.01 V
1744947617	12.71 V	273 mA	-247 mA	0.01 V
1744947015	12.71 V	282 mA	-256 mA	0.01 V
1744946418	12.71 V	280 mA	-254 mA	0.01 V
1744945818	12.72 V	272 mA	-246 mA	0.01 V
1744945218	12.72 V	277 mA	-252 mA	0.01 V
1744944618	12.73 V	280 mA	-255 mA	0.01 V
1744944018	12.73 V	274 mA	-248 mA	0.01 V
1744943416	12.73 V	283 mA	-258 mA	0.01 V
1744942818	12.74 V	279 mA	-253 mA	0.01 V
1744942218	12.75 V	270 mA	-245 mA	0.01 V
1744941618	12.75 V	274 mA	-248 mA	0.01 V
1744941018	12.76 V	270 mA	-245 mA	0.01 V
1744940418	12.76 V	273 mA	-248 mA	0.01 V
1744939815	12.77 V	281 mA	-256 mA	0.01 V
1744939218	12.77 V	279 mA	-254 mA	0.03 V

*Used Equation Coefficients:

Battery Voltage: 0, 0.01, 0

Battery Current: 0, 1, -4096

Load Current: 0, 1, -4096

Solar Voltage: 0, 0.01, 0

Solar Current: 0, 1, -4096

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)