APRS Track Direct

My position About ☰

reset

SR9WXL Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXL. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1732293034	72 Pkt	2 Pkt	0 Pkt
1732292434	76 Pkt	5 Pkt	1 Pkt
1732291829	83 Pkt	2 Pkt	0 Pkt
1732291229	88 Pkt	4 Pkt	0 Pkt
1732290627	83 Pkt	4 Pkt	2 Pkt
1732290028	100 Pkt	3 Pkt	0 Pkt
1732289425	102 Pkt	7 Pkt	0 Pkt
1732288812	83 Pkt	3 Pkt	0 Pkt
1732288210	72 Pkt	3 Pkt	0 Pkt
1732287610	83 Pkt	4 Pkt	0 Pkt
1732287008	72 Pkt	2 Pkt	0 Pkt
1732286408	84 Pkt	4 Pkt	0 Pkt
1732285803	104 Pkt	4 Pkt	2 Pkt
1732285203	106 Pkt	5 Pkt	1 Pkt
1732284601	98 Pkt	2 Pkt	0 Pkt
1732284001	87 Pkt	5 Pkt	2 Pkt
1732283399	102 Pkt	10 Pkt	7 Pkt
1732282796	85 Pkt	5 Pkt	2 Pkt
1732282195	79 Pkt	3 Pkt	0 Pkt
1732281595	71 Pkt	3 Pkt	0 Pkt
1732280994	63 Pkt	2 Pkt	0 Pkt
1732280394	69 Pkt	8 Pkt	0 Pkt
1732279778	70 Pkt	2 Pkt	0 Pkt
1732279178	78 Pkt	4 Pkt	0 Pkt
1732278575	68 Pkt	2 Pkt	0 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)