APRS Track Direct

My position About ☰

reset

YM2KBI-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM2KBI-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274426	0 Pkt	-69 dBm	12.2 V
1836274254	0 Pkt	-70 dBm	12.18 V
1765982182	3 Pkt	-69 dBm	12.14 V
1765981260	1 Pkt	-69 dBm	12.16 V
1765980338	3 Pkt	-70 dBm	12.16 V
1765979415	1 Pkt	-67 dBm	12.14 V
1765978493	3 Pkt	-68 dBm	12.16 V
1765977571	1 Pkt	-68 dBm	12.14 V
1765976649	3 Pkt	-67 dBm	12.16 V
1765975727	1 Pkt	-67 dBm	12.16 V
1765974805	3 Pkt	-64 dBm	12.14 V
1765973883	0 Pkt	-67 dBm	12.16 V
1765972961	3 Pkt	-66 dBm	12.14 V
1765972038	3 Pkt	-65 dBm	12.14 V
1765971116	3 Pkt	-67 dBm	12.14 V
1765970194	1 Pkt	-70 dBm	12.14 V
1765969272	3 Pkt	-67 dBm	12.14 V
1765968350	6 Pkt	-67 dBm	12.14 V
1765967428	3 Pkt	-68 dBm	12.14 V
1765966506	1 Pkt	-72 dBm	12.14 V
1765965584	3 Pkt	-66 dBm	12.16 V
1765964662	0 Pkt	-64 dBm	12.16 V
1765960867	1 Pkt	-65 dBm	12.18 V
1765959945	3 Pkt	-64 dBm	12.18 V
1765959023	1 Pkt	-68 dBm	12.16 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)