APRS Track Direct

My position About ☰

reset

S56RAL-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object S56RAL-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	I2*	U1*	Temp*
1836274814	0 A	12.5 Volt	20 C
1836274514	0 A	12.5 Volt	20.5 C
1836274364	0 A	12.5 Volt	21 C
1836274213	0 A	12.5 Volt	20.5 C
1836273913	0 A	12.5 Volt	21 C
1770171982	-0.2 A	12.7 Volt	16.5 C
1770171682	-0.2 A	12.7 Volt	16.5 C
1770171381	-0.2 A	12.7 Volt	16.5 C
1770171081	-0.2 A	12.7 Volt	16.5 C
1770170781	-0.2 A	12.7 Volt	16.5 C
1770170481	-0.2 A	12.7 Volt	16.5 C
1770170180	-0.2 A	12.7 Volt	16.5 C
1770169880	-0.2 A	12.7 Volt	16.5 C
1770169580	-0.2 A	12.7 Volt	16.5 C
1770169279	-0.2 A	12.7 Volt	16.5 C
1770168979	-0.2 A	12.7 Volt	16.5 C
1770168679	-0.2 A	12.7 Volt	16.5 C
1770168379	-0.2 A	12.7 Volt	16.5 C
1770168078	-0.2 A	12.7 Volt	16.5 C
1770167778	-0.2 A	12.7 Volt	16.5 C
1770162072	-0.2 A	14.1 Volt	16.5 C
1770161472	-0.2 A	14.1 Volt	16.5 C
1770160871	-0.2 A	14.1 Volt	16.5 C
1770160571	-0.2 A	13.9 Volt	16.5 C
1770160271	-0.2 A	13.3 Volt	16.5 C

*Used Equation Coefficients:

I1: 0, 0.1953, -24.9981

I2: 0, 0.1953, -24.9981

U1: 0, 0.1, 0

U2: 0, 0.5, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)