APRS Track Direct

My position About ☰

reset

METMOR Telemetry

This is the latest recevied telemetry packets stored in our database for station/object METMOR. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1836274541	13.73 Volt	910 Pkt	63 Pcnt
1836274391	13.73 Volt	920 Pkt	65 Pcnt
1836273941	13.73 Volt	930 Pkt	63 Pcnt
1766282912	13.65 Volt	150 Pkt	52 Pcnt
1766282312	13.73 Volt	150 Pkt	53 Pcnt
1766281712	13.73 Volt	160 Pkt	56 Pcnt
1766281112	13.73 Volt	180 Pkt	60 Pcnt
1766280512	13.65 Volt	210 Pkt	63 Pcnt
1766279912	13.65 Volt	220 Pkt	65 Pcnt
1766279312	13.65 Volt	240 Pkt	65 Pcnt
1766278712	13.73 Volt	260 Pkt	67 Pcnt
1766278112	13.65 Volt	250 Pkt	65 Pcnt
1766277512	13.65 Volt	240 Pkt	62 Pcnt
1766276912	13.65 Volt	230 Pkt	63 Pcnt
1766276312	13.73 Volt	230 Pkt	61 Pcnt
1766275712	13.65 Volt	250 Pkt	61 Pcnt
1766275112	13.73 Volt	250 Pkt	60 Pcnt
1766274512	13.73 Volt	250 Pkt	62 Pcnt
1766273912	13.73 Volt	260 Pkt	61 Pcnt
1766273312	13.73 Volt	270 Pkt	60 Pcnt
1766272712	13.73 Volt	260 Pkt	58 Pcnt
1766272112	13.65 Volt	240 Pkt	57 Pcnt
1766271512	13.65 Volt	230 Pkt	56 Pcnt
1766270912	13.73 Volt	230 Pkt	55 Pcnt
1766270312	13.73 Volt	220 Pkt	55 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)