APRS Track Direct

My position About ☰

reset

BX4ACP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX4ACP-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1766193667	26.5 C	68 p	137 p	1248 p
1766192466	26.9 C	34 p	98 p	1206 p
1766191267	26.8 C	35 p	94 p	1197 p
1766190067	26.4 C	29 p	77 p	1214 p
1766188866	26.5 C	30 p	68 p	1233 p
1766187667	26.6 C	18 p	57 p	1227 p
1766186466	26.3 C	20 p	66 p	1232 p
1766185267	26.3 C	19 p	78 p	1225 p
1766184067	27.6 C	27 p	84 p	1231 p
1766182867	26 C	32 p	70 p	1237 p
1766181667	23.9 C	25 p	54 p	1225 p
1766180467	24 C	13 p	45 p	1216 p
1766179267	24.1 C	16 p	48 p	1218 p
1766178067	24.3 C	16 p	48 p	1218 p
1766176867	23.6 C	16 p	47 p	1218 p
1766175667	24.9 C	16 p	45 p	1221 p
1766174467	24.9 C	15 p	44 p	1219 p
1766173267	23.9 C	14 p	47 p	1216 p
1766172067	24.2 C	15 p	43 p	1216 p
1766170867	23.7 C	18 p	42 p	1220 p
1766169666	24 C	10 p	33 p	1217 p
1766168467	24.1 C	14 p	46 p	1225 p
1766167267	24 C	9 p	58 p	1230 p
1766166067	24 C	23 p	68 p	1243 p
1766164866	24.7 C	26 p	60 p	1239 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)