APRS Track Direct

My position About ☰

reset

IR2UGU Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR2UGU. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Dg10m*	Eff1h*
1762326009	0 Pkt	0 Pkt	100 Pcnt
1762325711	0 Pkt	0 Pkt	100 Pcnt
1762325409	0 Pkt	0 Pkt	100 Pcnt
1762325108	0 Pkt	0 Pkt	100 Pcnt
1762324808	0 Pkt	0 Pkt	100 Pcnt
1762324508	0 Pkt	0 Pkt	100 Pcnt
1762324208	0 Pkt	0 Pkt	100 Pcnt
1762323907	0 Pkt	0 Pkt	100 Pcnt
1762323607	0 Pkt	0 Pkt	100 Pcnt
1762323309	0 Pkt	0 Pkt	100 Pcnt
1762323006	0 Pkt	0 Pkt	100 Pcnt
1762322706	0 Pkt	0 Pkt	100 Pcnt
1762322406	0 Pkt	0 Pkt	100 Pcnt
1762322107	0 Pkt	0 Pkt	100 Pcnt
1762321805	0 Pkt	0 Pkt	100 Pcnt
1762321505	0 Pkt	0 Pkt	100 Pcnt
1762321205	1 Pkt	1 Pkt	100 Pcnt
1762320904	1 Pkt	1 Pkt	100 Pcnt
1762320606	0 Pkt	0 Pkt	100 Pcnt
1762320304	0 Pkt	0 Pkt	100 Pcnt
1762320004	0 Pkt	0 Pkt	100 Pcnt
1762319705	0 Pkt	0 Pkt	100 Pcnt
1762319403	0 Pkt	0 Pkt	100 Pcnt
1762319103	0 Pkt	0 Pkt	100 Pcnt
1762318802	0 Pkt	0 Pkt	100 Pcnt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Dg10m: 0, 1, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)