APRS Track Direct

My position About ☰

reset

KD0M-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KD0M-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1790648758	116 Pkts	113 Pkts	61 Pkts	12 C
1790645158	111 Pkts	110 Pkts	66 Pkts	14 C
1790641558	79 Pkts	78 Pkts	63 Pkts	14 C
1790637958	113 Pkts	113 Pkts	76 Pkts	14 C
1790634359	125 Pkts	123 Pkts	68 Pkts	14 C
1790630759	121 Pkts	119 Pkts	71 Pkts	14 C
1790627159	102 Pkts	100 Pkts	61 Pkts	14 C
1790614938	117 Pkts	115 Pkts	68 Pkts	12 C
1790611338	152 Pkts	150 Pkts	85 Pkts	11 C
1790607738	156 Pkts	150 Pkts	75 Pkts	10 C
1790604138	171 Pkts	169 Pkts	66 Pkts	10 C
1790600538	190 Pkts	185 Pkts	79 Pkts	10 C
1790596938	203 Pkts	197 Pkts	81 Pkts	9 C
1790593338	214 Pkts	211 Pkts	82 Pkts	9 C
1790589738	234 Pkts	228 Pkts	80 Pkts	10 C
1790586138	209 Pkts	206 Pkts	72 Pkts	10 C
1790582538	216 Pkts	209 Pkts	71 Pkts	10 C
1790578938	187 Pkts	181 Pkts	65 Pkts	11 C
1790575338	187 Pkts	181 Pkts	68 Pkts	11 C
1790571738	172 Pkts	164 Pkts	73 Pkts	11 C
1790568138	152 Pkts	149 Pkts	60 Pkts	11 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)