APRS Track Direct

My position About ☰

reset

K8VAN-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K8VAN-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1758187911	13.88 Volt	230 Pkt	50 Pkt	38 Pcnt
1758187311	13.88 Volt	240 Pkt	50 Pkt	39 Pcnt
1758186710	13.88 Volt	230 Pkt	60 Pkt	39 Pcnt
1758186110	13.88 Volt	240 Pkt	60 Pkt	40 Pcnt
1758184909	13.88 Volt	240 Pkt	60 Pkt	43 Pcnt
1758184310	13.88 Volt	250 Pkt	50 Pkt	45 Pcnt
1758183715	13.88 Volt	260 Pkt	50 Pkt	46 Pcnt
1758183109	13.88 Volt	260 Pkt	50 Pkt	47 Pcnt
1758182510	13.88 Volt	280 Pkt	60 Pkt	50 Pcnt
1758181309	13.88 Volt	300 Pkt	60 Pkt	51 Pcnt
1758180711	13.88 Volt	290 Pkt	50 Pkt	50 Pcnt
1758180114	13.88 Volt	300 Pkt	50 Pkt	51 Pcnt
1758179510	13.88 Volt	290 Pkt	50 Pkt	50 Pcnt
1758178313	13.88 Volt	300 Pkt	50 Pkt	57 Pcnt
1758177710	13.88 Volt	310 Pkt	50 Pkt	61 Pcnt
1758176515	13.88 Volt	310 Pkt	60 Pkt	64 Pcnt
1758175912	13.95 Volt	290 Pkt	60 Pkt	65 Pcnt
1758175310	13.88 Volt	280 Pkt	60 Pkt	62 Pcnt
1758174715	13.88 Volt	270 Pkt	50 Pkt	59 Pcnt
1758174113	13.88 Volt	250 Pkt	50 Pkt	55 Pcnt
1758173512	13.88 Volt	250 Pkt	50 Pkt	56 Pcnt
1758172912	13.88 Volt	240 Pkt	40 Pkt	56 Pcnt
1758172311	13.88 Volt	230 Pkt	40 Pkt	53 Pcnt
1758171116	13.88 Volt	230 Pkt	40 Pkt	50 Pcnt
1758170511	13.88 Volt	210 Pkt	40 Pkt	49 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

I1: 0, 19.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)