APRS Track Direct

My position About ☰

reset

M0UPS-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object M0UPS-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BattSOC*	Volt*	Curr*	Rad*
1786729803	80 %	12.8 V	-0.5 A	9 uR/h
1786729503	80 %	12.8 V	-0.5 A	11 uR/h
1786729203	80 %	12.9 V	-0.5 A	5 uR/h
1786728903	80 %	12.9 V	-0.5 A	7 uR/h
1786728603	80 %	12.9 V	0 A	7 uR/h
1786728303	80 %	12.9 V	0 A	12 uR/h
1786728003	80 %	12.9 V	0 A	7 uR/h
1786727703	80 %	12.9 V	0 A	10 uR/h
1786727403	80 %	12.9 V	0 A	7 uR/h
1786727103	80 %	13 V	0 A	10 uR/h
1786726803	80 %	13.4 V	0 A	7 uR/h
1786726503	80 %	13.6 V	0 A	15 uR/h
1786726203	80 %	13.6 V	0 A	6 uR/h
1786725902	80 %	13.5 V	0 A	7 uR/h
1786725603	80 %	13.6 V	0 A	13 uR/h
1786725303	80 %	13.5 V	0 A	10 uR/h
1786725004	80 %	13.5 V	0 A	14 uR/h
1786724703	80 %	13.4 V	0 A	10 uR/h
1786724403	80 %	13.4 V	0 A	9 uR/h
1786724103	80 %	13.4 V	0 A	8 uR/h
1786723803	80 %	13.4 V	0 A	13 uR/h
1786723503	80 %	13.4 V	0 A	6 uR/h
1786723204	80 %	13.4 V	0 A	11 uR/h
1786722903	80 %	13.4 V	0 A	11 uR/h
1786722603	80 %	13.4 V	0 A	10 uR/h

*Used Equation Coefficients:

BattSOC: 0, 1, 0

Volt: 0, 0.1, 0

Curr: 0, 0.5, -50

Rad: 0, 1, 0

Unused: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)