APRS Track Direct

My position About ☰

reset

YH3NPX-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YH3NPX-6. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1752779002	0 Pkt	-36 dBm	13.39 V
1752774862	16 Pkt	-39 dBm	13.39 V
1752773892	16 Pkt	-38 dBm	13.39 V
1752772914	14 Pkt	-35 dBm	13.39 V
1752771957	17 Pkt	-38 dBm	13.39 V
1752769417	16 Pkt	-35 dBm	13.39 V
1752768449	14 Pkt	-37 dBm	13.39 V
1752762774	15 Pkt	-38 dBm	13.39 V
1752755795	11 Pkt	-35 dBm	13.39 V
1752754127	15 Pkt	-37 dBm	13.39 V
1752753161	14 Pkt	-36 dBm	13.39 V
1752751332	16 Pkt	-38 dBm	13.39 V
1752749804	14 Pkt	-41 dBm	13.39 V
1752745450	1 Pkt	-39 dBm	13.37 V
1752745112	14 Pkt	-32 dBm	13.39 V
1752743278	0 Pkt	-38 dBm	13.37 V
1752743235	16 Pkt	-32 dBm	13.39 V
1752740814	14 Pkt	-31 dBm	13.39 V
1752738376	1 Pkt	-39 dBm	13.37 V
1752736220	2 Pkt	-38 dBm	13.39 V
1752736156	6 Pkt	-35 dBm	13.39 V
1752732622	15 Pkt	-33 dBm	13.39 V
1752730816	1 Pkt	-39 dBm	13.37 V
1752730749	15 Pkt	-32 dBm	13.39 V
1752726217	14 Pkt	-39 dBm	13.39 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)