APRS Track Direct

My position About ☰

reset

ED1ZAD-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1ZAD-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RX1h*	DG1h*	Eff1h*
1836274737	640 Pkt	90 Pkt	72 Pcnt
1836274587	610 Pkt	80 Pkt	70 Pcnt
1836274439	670 Pkt	100 Pkt	73 Pcnt
1836274436	670 Pkt	100 Pkt	73 Pcnt
1836274287	620 Pkt	90 Pkt	71 Pcnt
1836274287	620 Pkt	90 Pkt	71 Pcnt
1836274136	690 Pkt	110 Pkt	72 Pcnt
1762349302	510 Pkt	50 Pkt	72 Pcnt
1762349302	510 Pkt	50 Pkt	72 Pcnt
1762349001	490 Pkt	50 Pkt	74 Pcnt
1762348703	480 Pkt	40 Pkt	72 Pcnt
1762348701	480 Pkt	40 Pkt	72 Pcnt
1762348401	480 Pkt	40 Pkt	72 Pcnt
1762348102	470 Pkt	40 Pkt	71 Pcnt
1762348100	470 Pkt	40 Pkt	71 Pcnt
1762347800	480 Pkt	40 Pkt	72 Pcnt
1762347502	470 Pkt	40 Pkt	73 Pcnt
1762347500	470 Pkt	40 Pkt	73 Pcnt
1762347200	490 Pkt	40 Pkt	73 Pcnt
1762346900	490 Pkt	40 Pkt	73 Pcnt
1762346899	490 Pkt	40 Pkt	73 Pcnt
1762346599	490 Pkt	40 Pkt	74 Pcnt
1762346302	490 Pkt	40 Pkt	73 Pcnt
1762346299	490 Pkt	40 Pkt	73 Pcnt
1762345998	480 Pkt	40 Pkt	74 Pcnt

*Used Equation Coefficients:

RX1h: 0, 10, 0

DG1h: 0, 10, 0

Eff1h: 0, 1, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)