APRS Track Direct

My position About ☰

reset

HS5ZEZ Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5ZEZ. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1786742987	0 Pkt	-44 dBm	13.88 V
1786742065	0 Pkt	-42 dBm	13.99 V
1786741143	1 Pkt	-41 dBm	13.99 V
1786740221	1 Pkt	-42 dBm	13.99 V
1786739299	0 Pkt	-43 dBm	13.97 V
1786738377	0 Pkt	-43 dBm	13.97 V
1786737455	0 Pkt	-42 dBm	13.99 V
1786736533	0 Pkt	-43 dBm	13.99 V
1786735611	0 Pkt	-42 dBm	13.97 V
1786734689	0 Pkt	-42 dBm	13.86 V
1786733767	0 Pkt	-44 dBm	13.99 V
1786732845	0 Pkt	-45 dBm	13.86 V
1786731923	0 Pkt	-44 dBm	13.86 V
1786731001	1 Pkt	-42 dBm	13.97 V
1786730079	0 Pkt	-43 dBm	13.97 V
1786729157	0 Pkt	-43 dBm	13.86 V
1786728235	0 Pkt	-42 dBm	13.9 V
1786727313	1 Pkt	-42 dBm	13.99 V
1786726391	0 Pkt	-43 dBm	13.99 V
1786725469	0 Pkt	-42 dBm	13.9 V
1786724547	0 Pkt	-44 dBm	13.99 V
1786723625	1 Pkt	-43 dBm	13.97 V
1786722703	1 Pkt	-42 dBm	13.99 V
1786721781	0 Pkt	-44 dBm	13.86 V
1786720859	0 Pkt	-42 dBm	13.97 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)