APRS Track Direct

My position About ☰

reset

HS6TIM Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS6TIM. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1836274843	0 Pkt	-77 dBm	10.03 V
1836274221	0 Pkt	-78 dBm	8.82 V
1770126212	1 Pkt	-76 dBm	9.41 V
1770125590	4 Pkt	-75 dBm	9.35 V
1770124938	2 Pkt	-77 dBm	9.35 V
1770124300	1 Pkt	-76 dBm	7.57 V
1770123678	1 Pkt	-76 dBm	8.88 V
1770123056	1 Pkt	-77 dBm	9.41 V
1770122433	1 Pkt	-74 dBm	7.65 V
1770121812	1 Pkt	-77 dBm	9.62 V
1770121190	1 Pkt	-78 dBm	9.17 V
1770120567	1 Pkt	-75 dBm	9.41 V
1770119945	1 Pkt	-79 dBm	8.67 V
1770119323	4 Pkt	-79 dBm	9.43 V
1770118670	0 Pkt	-76 dBm	9.47 V
1770118048	0 Pkt	-75 dBm	9.45 V
1770117426	0 Pkt	-74 dBm	9.41 V
1770116804	0 Pkt	-77 dBm	8.9 V
1770116182	0 Pkt	-75 dBm	9.27 V
1770115560	1 Pkt	-78 dBm	9.6 V
1770114938	1 Pkt	-77 dBm	9.62 V
1770114316	1 Pkt	-75 dBm	9.43 V
1770113693	1 Pkt	-75 dBm	9.62 V
1770113071	1 Pkt	-73 dBm	9.45 V
1770112448	0 Pkt	-73 dBm	9.54 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)