APRS Track Direct

My position About ☰

reset

VK5RBV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK5RBV-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dig1h*	Eff1h*
1779765004	13.76 Volt	24 Pkt	3 Pkt	97 Pcnt
1779761400	13.76 Volt	22 Pkt	3 Pkt	90 Pcnt
1779757797	13.76 Volt	16 Pkt	3 Pkt	95 Pcnt
1779754193	13.76 Volt	16 Pkt	3 Pkt	87 Pcnt
1779750590	13.76 Volt	20 Pkt	3 Pkt	88 Pcnt
1779746986	13.76 Volt	15 Pkt	3 Pkt	92 Pcnt
1779743383	13.76 Volt	16 Pkt	3 Pkt	89 Pcnt
1779739779	13.76 Volt	15 Pkt	3 Pkt	83 Pcnt
1779736176	13.76 Volt	16 Pkt	3 Pkt	90 Pcnt
1779732572	13.76 Volt	15 Pkt	3 Pkt	92 Pcnt
1779728969	13.76 Volt	15 Pkt	3 Pkt	93 Pcnt
1779725365	13.76 Volt	13 Pkt	3 Pkt	91 Pcnt
1779721762	13.76 Volt	14 Pkt	3 Pkt	93 Pcnt
1779718158	13.76 Volt	14 Pkt	3 Pkt	91 Pcnt
1779714555	13.76 Volt	14 Pkt	3 Pkt	94 Pcnt
1779710951	13.76 Volt	13 Pkt	3 Pkt	97 Pcnt
1779707348	13.76 Volt	13 Pkt	3 Pkt	96 Pcnt
1779703745	13.76 Volt	13 Pkt	3 Pkt	97 Pcnt
1779700141	13.76 Volt	15 Pkt	3 Pkt	95 Pcnt
1779696537	13.76 Volt	22 Pkt	3 Pkt	97 Pcnt
1779692934	13.76 Volt	21 Pkt	3 Pkt	93 Pcnt
1779689331	13.54 Volt	19 Pkt	3 Pkt	97 Pcnt
1779685727	13.69 Volt	19 Pkt	3 Pkt	87 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.074, 0

Rx1h: 0, 1, 0

Dig1h: 0, 1, 0

Eff1h: 0, 1, 0

Temp: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)