APRS Track Direct

My position About ☰

reset

S51W-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object S51W-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1836274768	13.71 Volt	0 Pkt	0 Pkt	0 Pcnt
1836273868	13.71 Volt	0 Pkt	0 Pkt	0 Pcnt
1770140752	13.71 Volt	380 Pkt	120 Pkt	68 Pcnt
1770139851	13.71 Volt	390 Pkt	120 Pkt	68 Pcnt
1770138950	13.71 Volt	410 Pkt	130 Pkt	68 Pcnt
1770138049	13.63 Volt	410 Pkt	120 Pkt	65 Pcnt
1770137148	13.71 Volt	420 Pkt	110 Pkt	64 Pcnt
1770136248	13.71 Volt	420 Pkt	110 Pkt	64 Pcnt
1770135347	13.71 Volt	390 Pkt	100 Pkt	62 Pcnt
1770134446	13.71 Volt	360 Pkt	100 Pkt	59 Pcnt
1770133546	13.71 Volt	300 Pkt	80 Pkt	50 Pcnt
1770133545	13.71 Volt	300 Pkt	80 Pkt	50 Pcnt
1770132645	13.71 Volt	260 Pkt	70 Pkt	44 Pcnt
1770132644	13.71 Volt	260 Pkt	70 Pkt	44 Pcnt
1770131743	13.71 Volt	210 Pkt	60 Pkt	37 Pcnt
1770130842	13.71 Volt	200 Pkt	50 Pkt	35 Pcnt
1770129941	13.71 Volt	190 Pkt	50 Pkt	36 Pcnt
1770129041	13.71 Volt	170 Pkt	40 Pkt	33 Pcnt
1770128140	13.71 Volt	170 Pkt	40 Pkt	33 Pcnt
1770127239	13.71 Volt	180 Pkt	50 Pkt	34 Pcnt
1770126338	13.71 Volt	210 Pkt	60 Pkt	38 Pcnt
1770125437	13.63 Volt	210 Pkt	70 Pkt	37 Pcnt
1770124538	13.71 Volt	210 Pkt	70 Pkt	35 Pcnt
1770124536	13.71 Volt	210 Pkt	70 Pkt	35 Pcnt
1770123635	13.71 Volt	210 Pkt	70 Pkt	35 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.077, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)