APRS Track Direct

My position About ☰

reset

HS3LSE-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS3LSE-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	TxTraffic*	RSSI*	Voltage*
1732297803	237 Pkt	0 Pkt	-64 dBm	0.27 V
1732295072	77 Pkt	0 Pkt	-64 dBm	0.1 V
1732292345	14 Pkt	0 Pkt	-61 dBm	0.27 V
1732289618	137 Pkt	0 Pkt	-59 dBm	0.27 V
1732286889	60 Pkt	1 Pkt	-61 dBm	0.1 V
1732284162	66 Pkt	0 Pkt	-60 dBm	0.27 V
1732281434	111 Pkt	0 Pkt	-61 dBm	0.1 V
1732278706	135 Pkt	0 Pkt	-62 dBm	0.1 V
1732275978	86 Pkt	0 Pkt	-61 dBm	0.1 V
1732273250	92 Pkt	1 Pkt	-70 dBm	0.1 V
1732270521	65 Pkt	1 Pkt	-67 dBm	0.1 V
1732267794	38 Pkt	3 Pkt	-64 dBm	0.29 V
1732265067	10 Pkt	1 Pkt	-66 dBm	0.1 V
1732262340	75 Pkt	2 Pkt	-66 dBm	0.1 V
1732259612	83 Pkt	0 Pkt	-61 dBm	0.1 V
1732256884	56 Pkt	3 Pkt	-64 dBm	0.1 V
1732254156	35 Pkt	2 Pkt	-62 dBm	0.27 V
1732251429	36 Pkt	0 Pkt	-70 dBm	0.1 V
1732248702	165 Pkt	0 Pkt	-69 dBm	0.1 V
1732245970	108 Pkt	0 Pkt	-65 dBm	0.27 V
1732243239	85 Pkt	0 Pkt	-68 dBm	0.27 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)