APRS Track Direct

My position About ☰

reset

LU8SAM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU8SAM-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1774482525	10 Pkt	-29 dBm	0.62 V
1774481281	15 Pkt	-27 dBm	0.59 V
1774480658	14 Pkt	-27 dBm	0.59 V
1774480036	12 Pkt	-29 dBm	0.59 V
1774479413	3 Pkt	-28 dBm	0.62 V
1774478750	12 Pkt	-27 dBm	0.62 V
1774478127	12 Pkt	-26 dBm	0.62 V
1774477505	8 Pkt	-27 dBm	0.62 V
1774476882	14 Pkt	-27 dBm	0.62 V
1774475638	9 Pkt	-27 dBm	0.62 V
1774475016	10 Pkt	-29 dBm	0.62 V
1774473771	10 Pkt	-28 dBm	0.62 V
1774472526	12 Pkt	-29 dBm	0.62 V
1774471904	7 Pkt	-29 dBm	0.62 V
1774471282	4 Pkt	-28 dBm	0.78 V
1774470660	7 Pkt	-28 dBm	0.64 V
1774470037	8 Pkt	-30 dBm	0.62 V
1774469415	6 Pkt	-27 dBm	0.62 V
1774468793	7 Pkt	-30 dBm	0.64 V
1774467548	6 Pkt	-27 dBm	0.64 V
1774466926	6 Pkt	-28 dBm	0.64 V
1774466304	7 Pkt	-27 dBm	0.64 V
1774465682	8 Pkt	-28 dBm	0.64 V
1774465060	5 Pkt	-27 dBm	0.64 V
1774464438	6 Pkt	-27 dBm	0.64 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)