APRS Track Direct

My position About ☰

reset

BG9EGA-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BG9EGA-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	CPUTemp*	DiGi*	Tx*	Rx*
1786723251	65 C	0 p	1 p	1 p
1786719651	65 C	3 p	24 p	799 p
1786716051	65 C	3 p	23 p	779 p
1786712452	66 C	3 p	22 p	700 p
1786708852	66 C	2 p	21 p	644 p
1786705252	67 C	1 p	20 p	591 p
1786701652	67 C	1 p	19 p	565 p
1786698052	66 C	1 p	18 p	534 p
1786694452	66 C	0 p	17 p	466 p
1786690852	65 C	0 p	16 p	447 p
1786687251	64 C	0 p	15 p	426 p
1786683651	63 C	0 p	14 p	395 p
1786680052	62 C	0 p	13 p	360 p
1786676453	62 C	0 p	12 p	334 p
1786672852	61 C	0 p	11 p	314 p
1786669252	61 C	0 p	10 p	285 p
1786665652	61 C	0 p	9 p	193 p
1786662052	61 C	0 p	8 p	152 p
1786658451	61 C	0 p	7 p	128 p
1786654851	62 C	0 p	6 p	106 p
1786651251	62 C	0 p	5 p	82 p
1786647652	62 C	0 p	4 p	61 p
1786644052	62 C	0 p	3 p	41 p
1786640452	63 C	0 p	2 p	22 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

DiGi: 0, 1, 0

Tx: 0, 1, 0

Rx: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)