APRS Track Direct

My position About ☰

reset

AI5TX-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI5TX-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1758213012	13.58 Volt	150 Pkt	60 Pkt	37 Pcnt
1758209354	13.58 Volt	260 Pkt	80 Pkt	40 Pcnt
1758205754	13.58 Volt	550 Pkt	160 Pkt	47 Pcnt
1758202154	13.58 Volt	460 Pkt	150 Pkt	48 Pcnt
1758198556	13.58 Volt	230 Pkt	90 Pkt	32 Pcnt
1758198554	13.58 Volt	230 Pkt	90 Pkt	32 Pcnt
1758194954	13.58 Volt	180 Pkt	70 Pkt	42 Pcnt
1758191354	13.65 Volt	160 Pkt	60 Pkt	40 Pcnt
1758187754	13.65 Volt	160 Pkt	70 Pkt	40 Pcnt
1758184155	13.65 Volt	120 Pkt	50 Pkt	35 Pcnt
1758180555	13.58 Volt	100 Pkt	50 Pkt	37 Pcnt
1758176955	13.65 Volt	90 Pkt	50 Pkt	30 Pcnt
1758173355	13.58 Volt	70 Pkt	40 Pkt	31 Pcnt
1758169755	13.58 Volt	110 Pkt	60 Pkt	36 Pcnt
1758166155	13.58 Volt	130 Pkt	70 Pkt	50 Pcnt
1758162555	13.65 Volt	140 Pkt	70 Pkt	57 Pcnt
1758158955	13.65 Volt	110 Pkt	60 Pkt	52 Pcnt
1758155355	13.65 Volt	150 Pkt	70 Pkt	57 Pcnt
1758151755	13.58 Volt	100 Pkt	50 Pkt	53 Pcnt
1758148155	13.65 Volt	90 Pkt	60 Pkt	48 Pcnt
1758144555	13.65 Volt	90 Pkt	50 Pkt	45 Pcnt
1758140955	13.58 Volt	110 Pkt	80 Pkt	51 Pcnt
1758137355	13.65 Volt	100 Pkt	70 Pkt	50 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)