APRS Track Direct

My position About ☰

reset

VK5RLD-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK5RLD-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1790654065	14.1 Volt	91 Pcnt	32 C
1790653165	14.1 Volt	89 Pcnt	31.5 C
1790652264	14.1 Volt	86 Pcnt	31 C
1790651363	14.1 Volt	88 Pcnt	30.5 C
1790650462	14.1 Volt	91 Pcnt	30 C
1790649561	14.1 Volt	91 Pcnt	29.5 C
1790648660	14.1 Volt	94 Pcnt	29 C
1790647759	14.1 Volt	91 Pcnt	28.5 C
1790646859	14.1 Volt	87 Pcnt	27.5 C
1790645958	14.1 Volt	84 Pcnt	27 C
1790645057	14.03 Volt	75 Pcnt	26 C
1790644156	14.03 Volt	78 Pcnt	25.5 C
1790643255	14.7 Volt	77 Pcnt	24.5 C
1790642354	14.63 Volt	78 Pcnt	24 C
1790641453	14.7 Volt	81 Pcnt	23 C
1790640553	14.7 Volt	76 Pcnt	22.5 C
1790639652	14.7 Volt	80 Pcnt	21.5 C
1790638751	14.33 Volt	81 Pcnt	20.5 C
1790637850	14.63 Volt	81 Pcnt	19.5 C
1790636949	14.63 Volt	82 Pcnt	18.5 C
1790636048	13.43 Volt	73 Pcnt	18 C
1790635147	13.35 Volt	71 Pcnt	17.5 C
1790634246	13.73 Volt	74 Pcnt	17 C
1790633346	13.28 Volt	75 Pcnt	16.5 C
1790632445	12.98 Volt	81 Pcnt	15.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

U1: 0, 0.1, 0

U2: 0, 0.1, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)