APRS Track Direct

My position About ☰

reset

E24QND-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24QND-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	TxTraffic*	RxDrop*	RSSI*	Voltage*
1732272071	4 Pkt	4 Pkt	11 Pkt	-42 dBm	0.04 V
1732270244	9 Pkt	4 Pkt	11 Pkt	-44 dBm	0.06 V
1732268417	8 Pkt	3 Pkt	17 Pkt	-46 dBm	0.04 V
1732266589	20 Pkt	3 Pkt	25 Pkt	-40 dBm	0.06 V
1732264762	6 Pkt	7 Pkt	10 Pkt	-40 dBm	0.04 V
1732262934	2 Pkt	4 Pkt	7 Pkt	-41 dBm	0.04 V
1732261108	2 Pkt	3 Pkt	10 Pkt	-40 dBm	0.04 V
1732259283	16 Pkt	3 Pkt	21 Pkt	-40 dBm	0.04 V
1732257455	1 Pkt	3 Pkt	11 Pkt	-42 dBm	0.06 V
1732255628	6 Pkt	7 Pkt	6 Pkt	-43 dBm	0.04 V
1732253802	2 Pkt	3 Pkt	11 Pkt	-43 dBm	0.06 V
1732251976	2 Pkt	4 Pkt	6 Pkt	-42 dBm	0.06 V
1732250149	2 Pkt	4 Pkt	10 Pkt	-42 dBm	0.06 V
1732248323	5 Pkt	3 Pkt	7 Pkt	-41 dBm	0.06 V
1732246496	6 Pkt	6 Pkt	11 Pkt	-42 dBm	0.08 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)