APRS Track Direct

My position About ☰

reset

BUFBOY Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BUFBOY. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Value1*	Value2*	Value3*	Value4*
1836274686	12.9	0	2.75	2.71
1778054627	12.7	0	2.65	2.64
1778053729	12.7	0	2.65	2.64
1778043828	12.8	0	2.67	2.65
1778037527	12.9	0	2.67	2.65
1778035727	12.9	0	2.67	2.67
1778034827	12.9	0.1	2.69	2.67
1778033927	12.9	1.6	2.69	2.67
1778033027	12.9	5.6	2.69	2.67
1778032127	13	13.3	2.69	2.67
1778031227	13	13.4	2.69	2.69
1778030327	13.1	13.5	2.71	2.69
1778029427	13.1	13.5	2.71	2.69
1778025827	13.8	14.1	2.71	2.69
1778024027	13.9	14.2	2.71	2.71
1778023127	13.7	14.1	2.73	2.71
1778022227	13.7	0.1	2.73	2.71
1778021327	13.8	0.1	2.71	2.71
1778020427	14.3	0.1	2.73	2.71
1778019527	14.3	14.8	2.73	2.71
1778018628	13.8	14.2	2.71	2.71
1778017727	14.1	14.4	2.71	2.71
1778016827	14.1	0	2.71	2.71
1778015027	13.8	0.1	2.71	2.71
1778014127	13.9	0	2.71	2.71

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)