APRS Track Direct

My position About ☰

reset

YO8A-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO8A-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp_Procesor*	Temp_int*	Temp_ext*	None*
1786784472	64.8 C	55.1 C	16.7 C	648 C
1786783871	63.8 C	55.1 C	16.9 C	638 C
1786782074	61.6 C	43.2 C	15.4 C	616 C
1786781471	60 C	43.2 C	15.2 C	600 C
1786780871	58.9 C	43.2 C	15.2 C	0 C
1786780271	58.4 C	43.2 C	15.2 C	0 C
1786779671	56.2 C	43.2 C	15.2 C	562 C
1786779071	55.1 C	43.2 C	15.2 C	551 C
1786778473	54.1 C	43.2 C	12.3 C	0 C
1786777870	53 C	43.2 C	12.3 C	0 C
1786777272	51.9 C	42.6 C	12.3 C	0 C
1786776671	50.8 C	42.1 C	12.3 C	0 C
1786776071	50.8 C	41.6 C	12.3 C	0 C
1786775470	49.2 C	40.6 C	12.3 C	0 C
1786774873	48.7 C	39.3 C	12.3 C	0 C
1786774270	47.6 C	37.9 C	12.3 C	0 C
1786773671	46.5 C	35.2 C	12.3 C	0 C
1786773071	44.4 C	35.2 C	12.3 C	0 C
1786772471	43.9 C	33.4 C	12.3 C	0 C
1786771871	43.3 C	33.4 C	12.3 C	0 C
1786771274	42.8 C	32.9 C	12.3 C	0 C
1786770671	42.8 C	32.6 C	12.3 C	0 C
1786770071	42.2 C	32.4 C	12.3 C	0 C
1786769470	42.2 C	32.3 C	12.3 C	0 C
1786768871	42.2 C	32.1 C	12.3 C	0 C

*Used Equation Coefficients:

Temp_Procesor: 0, 0.1, 0

Temp_int: 0, 0.1, 0

Temp_ext: 0, 0.1, 0

None: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)