APRS Track Direct

My position About ☰

reset

TA4TX-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA4TX-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	DcIn*	Temp*	Gps*	TxCnt*
1786698699	12.5 Volt	43.9 *C	8 Satt	209 Pcs
1786698396	12.5 Volt	44 *C	8 Satt	208 Pcs
1786696890	10.8 Volt	43.3 *C	7 Satt	203 Pcs
1786696288	10.7 Volt	43 *C	8 Satt	201 Pcs
1786695686	10.6 Volt	42.7 *C	7 Satt	199 Pcs
1786695387	10.8 Volt	42.6 *C	7 Satt	198 Pcs
1786695086	10.6 Volt	42.5 *C	8 Satt	197 Pcs
1786694184	10.7 Volt	42 *C	8 Satt	194 Pcs
1786693881	10.8 Volt	41.8 *C	7 Satt	193 Pcs
1786693581	10.8 Volt	41.6 *C	8 Satt	192 Pcs
1786692978	10.7 Volt	41.3 *C	8 Satt	190 Pcs
1786692675	10.8 Volt	41.1 *C	8 Satt	189 Pcs
1786692375	10.7 Volt	40.8 *C	9 Satt	188 Pcs
1786691472	10.8 Volt	40.2 *C	8 Satt	185 Pcs
1786690268	10.8 Volt	39.4 *C	7 Satt	181 Pcs
1786689970	10.9 Volt	39.2 *C	7 Satt	180 Pcs
1786689667	10.8 Volt	39 *C	7 Satt	179 Pcs
1786689365	10.8 Volt	38.9 *C	7 Satt	178 Pcs
1786689064	10.7 Volt	38.6 *C	7 Satt	177 Pcs
1786687558	10.8 Volt	37.5 *C	6 Satt	172 Pcs
1786687256	10.7 Volt	37.3 *C	6 Satt	171 Pcs
1786686955	10.8 Volt	37 *C	6 Satt	170 Pcs
1786686355	10.7 Volt	36.3 *C	7 Satt	168 Pcs
1786686057	10.7 Volt	35.9 *C	7 Satt	167 Pcs
1786685753	10.8 Volt	35.4 *C	8 Satt	166 Pcs

*Used Equation Coefficients:

DcIn: 0, 0.1, 0

Ext.AIn: 0, 0.1, 0

Temp: 0, 0.1, 0

Gps: 0, 1, 0

TxCnt: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)