APRS Track Direct

My position About ☰

reset

E24RAM-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24RAM-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1750147293	1 Pkt	-54 dBm	0 V
1750145483	0 Pkt	-56 dBm	0.04 V
1750143673	0 Pkt	-54 dBm	0.04 V
1750141863	0 Pkt	-52 dBm	0.02 V
1750140053	1 Pkt	-53 dBm	0.04 V
1750138243	0 Pkt	-51 dBm	0 V
1750136433	0 Pkt	-49 dBm	0.04 V
1750134549	0 Pkt	-50 dBm	0.02 V
1750132739	1 Pkt	-50 dBm	0 V
1750130929	0 Pkt	-51 dBm	0 V
1750129119	1 Pkt	-52 dBm	0.04 V
1750127309	1 Pkt	-50 dBm	0.02 V
1750125499	1 Pkt	-50 dBm	0.02 V
1750123689	2 Pkt	-50 dBm	0.06 V
1750121879	1 Pkt	-51 dBm	0.02 V
1750120069	0 Pkt	-53 dBm	0.02 V
1750118259	0 Pkt	-51 dBm	0.02 V
1750116373	0 Pkt	-50 dBm	0.02 V
1750114563	0 Pkt	-52 dBm	0.02 V
1750112753	0 Pkt	-52 dBm	0 V
1750110943	1 Pkt	-51 dBm	0.04 V
1750109133	0 Pkt	-50 dBm	0.02 V
1750107323	0 Pkt	-51 dBm	0.04 V
1750105513	0 Pkt	-51 dBm	0.04 V
1750103703	0 Pkt	-51 dBm	0.02 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)