APRS Track Direct

My position About ☰

reset

AI5TX-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI5TX-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1782535954	13.5 Volt	90 Pkt	20 Pkt	39 Pcnt
1782532354	13.5 Volt	10 Pkt	0 Pkt	21 Pcnt
1782528754	13.5 Volt	10 Pkt	0 Pkt	18 Pcnt
1782525154	13.5 Volt	10 Pkt	0 Pkt	17 Pcnt
1782521554	13.5 Volt	10 Pkt	0 Pkt	16 Pcnt
1782517955	13.5 Volt	0 Pkt	0 Pkt	6 Pcnt
1782514355	13.5 Volt	10 Pkt	0 Pkt	18 Pcnt
1782510755	13.5 Volt	10 Pkt	0 Pkt	17 Pcnt
1782507155	13.5 Volt	10 Pkt	0 Pkt	14 Pcnt
1782503555	13.5 Volt	20 Pkt	0 Pkt	21 Pcnt
1782499955	13.5 Volt	30 Pkt	0 Pkt	29 Pcnt
1782496355	13.5 Volt	50 Pkt	0 Pkt	34 Pcnt
1782492755	13.5 Volt	50 Pkt	0 Pkt	31 Pcnt
1782489155	13.5 Volt	60 Pkt	10 Pkt	36 Pcnt
1782485555	13.5 Volt	50 Pkt	10 Pkt	36 Pcnt
1782481955	13.5 Volt	60 Pkt	10 Pkt	36 Pcnt
1782478355	13.5 Volt	50 Pkt	10 Pkt	30 Pcnt
1782474755	13.5 Volt	60 Pkt	0 Pkt	34 Pcnt
1782471156	13.5 Volt	50 Pkt	0 Pkt	31 Pcnt
1782467556	13.5 Volt	40 Pkt	0 Pkt	29 Pcnt
1782463956	13.5 Volt	30 Pkt	0 Pkt	18 Pcnt
1782460356	13.5 Volt	40 Pkt	0 Pkt	18 Pcnt
1782456756	13.5 Volt	40 Pkt	10 Pkt	18 Pcnt
1782453156	13.5 Volt	30 Pkt	0 Pkt	21 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)