APRS Track Direct

My position About ☰

reset

E22ULT-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E22ULT-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1786737979	19 Pkt	31 dBm	14.77 V
1786736145	17 Pkt	31 dBm	14.77 V
1786734316	21 Pkt	31 dBm	14.77 V
1786732485	13 Pkt	31 dBm	14.77 V
1786730656	16 Pkt	31 dBm	14.72 V
1786728826	18 Pkt	31 dBm	14.72 V
1786726994	14 Pkt	31 dBm	14.72 V
1786725163	18 Pkt	31 dBm	14.72 V
1786723332	17 Pkt	31 dBm	14.72 V
1786721501	15 Pkt	31 dBm	14.68 V
1786719670	14 Pkt	31 dBm	14.68 V
1786717839	6 Pkt	31 dBm	14.68 V
1786716013	2 Pkt	31 dBm	14.68 V
1786714187	3 Pkt	31 dBm	14.68 V
1786712361	3 Pkt	31 dBm	14.68 V
1786710534	3 Pkt	31 dBm	14.68 V
1786708708	3 Pkt	31 dBm	14.68 V
1786706882	3 Pkt	31 dBm	14.68 V
1786705056	4 Pkt	31 dBm	14.66 V
1786703230	2 Pkt	31 dBm	14.66 V
1786701404	8 Pkt	31 dBm	14.66 V
1786699576	13 Pkt	31 dBm	14.68 V
1786697747	14 Pkt	31 dBm	14.66 V
1786695917	12 Pkt	31 dBm	14.64 V
1786694089	13 Pkt	31 dBm	14.66 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)