APRS Track Direct

My position About ☰

reset

KC2G Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC2G. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BatTemp*	Bat*	Solar*
1758183549	66 deg.F	13 V	10 V
1758183245	66 deg.F	13 V	10 V
1758183244	66 deg.F	13 V	10 V
1758182948	66 deg.F	13.05 V	10 V
1758182349	66 deg.F	13.05 V	10 V
1758182344	66 deg.F	13.05 V	10 V
1758181749	67 deg.F	13 V	10 V
1758181445	67 deg.F	13.05 V	10 V
1758181444	67 deg.F	13.05 V	10 V
1758181149	67 deg.F	13.05 V	10 V
1758180548	67 deg.F	13.05 V	10 V
1758180544	67 deg.F	13.05 V	10 V
1758180543	67 deg.F	13.05 V	10 V
1758179949	68 deg.F	13 V	10 V
1758179645	68 deg.F	13.05 V	10 V
1758179644	68 deg.F	13.05 V	10 V
1758179348	68 deg.F	13.05 V	10 V
1758178748	68 deg.F	13.05 V	10 V
1758178747	68 deg.F	13.05 V	10 V
1758178743	68 deg.F	13.05 V	10 V
1758178149	68 deg.F	13.05 V	10 V
1758177845	68 deg.F	13.05 V	10 V
1758177844	68 deg.F	13.05 V	10 V
1758177548	68 deg.F	13.05 V	10 V
1758176948	68 deg.F	13.05 V	10 V

*Used Equation Coefficients:

BatTemp: 0, 0.5, 0

Bat: 0, 0.05, 10

ChgA: 0, 0.05, 0

Solar: 0, 0.05, 10

Chg: 0.002, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)