APRS Track Direct

My position About ☰

reset

9M2TDX-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9M2TDX-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RSSI*	Voltage*
1770083893	0 Pkt	-66 dBm	12.86 V
1770082095	0 Pkt	-66 dBm	12.86 V
1770081224	6 Pkt	-67 dBm	12.86 V
1770080299	0 Pkt	-64 dBm	12.84 V
1770078500	0 Pkt	-67 dBm	12.86 V
1770077622	0 Pkt	-64 dBm	12.88 V
1770076697	0 Pkt	-66 dBm	12.86 V
1770074900	0 Pkt	-65 dBm	12.86 V
1770074022	0 Pkt	-67 dBm	12.86 V
1770073097	0 Pkt	-68 dBm	12.88 V
1770071298	0 Pkt	-72 dBm	12.86 V
1770070422	0 Pkt	-65 dBm	12.88 V
1770069498	0 Pkt	-69 dBm	12.88 V
1770067698	0 Pkt	-68 dBm	12.86 V
1770066831	0 Pkt	-67 dBm	12.86 V
1770065906	0 Pkt	-67 dBm	12.88 V
1770064105	0 Pkt	-65 dBm	12.86 V
1770063237	0 Pkt	-65 dBm	12.88 V
1770062311	1 Pkt	-67 dBm	12.88 V
1770060512	0 Pkt	-69 dBm	12.86 V
1770059962	0 Pkt	-68 dBm	12.86 V
1770059037	0 Pkt	-67 dBm	12.88 V
1770056905	0 Pkt	-68 dBm	12.84 V
1770056028	0 Pkt	-66 dBm	12.86 V
1770055103	0 Pkt	-67 dBm	12.86 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)