APRS Track Direct

My position About ☰

reset

HS4RBP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS4RBP-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1766173101	0 Pkt	-69 dBm	4.25 V
1766171879	0 Pkt	-68 dBm	16.55 V
1766170657	0 Pkt	-67 dBm	19.48 V
1766169435	0 Pkt	-67 dBm	17 V
1766168213	0 Pkt	-70 dBm	16.1 V
1766166991	0 Pkt	-69 dBm	21 V
1766165769	3 Pkt	-67 dBm	18.33 V
1766164547	0 Pkt	-67 dBm	4.68 V
1766163325	0 Pkt	-70 dBm	16.28 V
1766162110	2 Pkt	-68 dBm	0.59 V
1766160881	0 Pkt	-69 dBm	21 V
1766159659	3 Pkt	-70 dBm	0 V
1766158437	0 Pkt	-70 dBm	0.62 V
1766157215	0 Pkt	-69 dBm	3.1 V
1766155993	0 Pkt	-69 dBm	18.54 V
1766154771	2 Pkt	-71 dBm	21 V
1766153549	0 Pkt	-70 dBm	18.83 V
1766152378	0 Pkt	-68 dBm	3.86 V
1766151106	1 Pkt	-70 dBm	5.58 V
1766149883	0 Pkt	-69 dBm	21 V
1766148661	2 Pkt	-69 dBm	11.24 V
1766147439	0 Pkt	-69 dBm	21 V
1766146217	1 Pkt	-68 dBm	0.86 V
1766144996	0 Pkt	-68 dBm	0.39 V
1766143772	0 Pkt	-68 dBm	1.15 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)