APRS Track Direct

My position About ☰

reset

YM7KO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM7KO. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	AKU*	TEMP*	RX*
1732475862	14.55 V.	20 C.	20 Pkt
1732475562	14.48 V.	20 C.	34 Pkt
1732475262	14.55 V.	20 C.	32 Pkt
1732474962	14.4 V.	20 C.	25 Pkt
1732474662	14.48 V.	20 C.	39 Pkt
1732474362	14.48 V.	20 C.	61 Pkt
1732474063	14.48 V.	20 C.	30 Pkt
1732473762	14.4 V.	20 C.	22 Pkt
1732473462	14.48 V.	20 C.	40 Pkt
1732473162	14.48 V.	20 C.	68 Pkt
1732472862	14.48 V.	20 C.	52 Pkt
1732472562	14.48 V.	20 C.	37 Pkt
1732472263	14.48 V.	20 C.	46 Pkt
1732471963	14.4 V.	19.5 C.	42 Pkt
1732471662	14.48 V.	19.5 C.	45 Pkt
1732471363	14.48 V.	19.5 C.	39 Pkt
1732471063	14.55 V.	20 C.	56 Pkt
1732470763	14.48 V.	20 C.	68 Pkt
1732470463	14.55 V.	20 C.	65 Pkt
1732470163	14.48 V.	20 C.	78 Pkt
1732469863	14.48 V.	20 C.	66 Pkt
1732469563	14.55 V.	19.5 C.	59 Pkt
1732469263	14.48 V.	19.5 C.	71 Pkt
1732468963	14.48 V.	19.5 C.	97 Pkt
1732468663	14.4 V.	20 C.	87 Pkt

*Used Equation Coefficients:

AKU: 0, 0.075, 0

PANEL: 0, 0.2, 0

WIND: 0, 0.2, 0

TEMP: 0, 0.5, -64

RX: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)