APRS Track Direct

My position About ☰

reset

W5HRH-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W5HRH-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1786734373	9 Pkts	7 Pkts	3 Pkts	36 C
1786730773	1 Pkts	1 Pkts	1 Pkts	36 C
1786727173	6 Pkts	5 Pkts	2 Pkts	36 C
1786723573	4 Pkts	4 Pkts	1 Pkts	36 C
1786719973	46 Pkts	42 Pkts	18 Pkts	36 C
1786716373	174 Pkts	164 Pkts	74 Pkts	40 C
1786712773	230 Pkts	224 Pkts	112 Pkts	41 C
1786709173	170 Pkts	165 Pkts	74 Pkts	41 C
1786705573	122 Pkts	111 Pkts	38 Pkts	41 C
1786701973	89 Pkts	82 Pkts	34 Pkts	41 C
1786698373	107 Pkts	96 Pkts	44 Pkts	41 C
1786694773	109 Pkts	98 Pkts	41 Pkts	41 C
1786691173	83 Pkts	69 Pkts	30 Pkts	41 C
1786687573	89 Pkts	80 Pkts	37 Pkts	41 C
1786683973	94 Pkts	80 Pkts	38 Pkts	41 C
1786680373	69 Pkts	57 Pkts	28 Pkts	41 C
1786676773	90 Pkts	80 Pkts	51 Pkts	41 C
1786673173	88 Pkts	77 Pkts	44 Pkts	41 C
1786669573	84 Pkts	73 Pkts	46 Pkts	41 C
1786665973	44 Pkts	41 Pkts	9 Pkts	40 C
1786662373	20 Pkts	16 Pkts	8 Pkts	37 C
1786658773	8 Pkts	5 Pkts	3 Pkts	36 C
1786655173	15 Pkts	14 Pkts	10 Pkts	37 C
1786651573	28 Pkts	19 Pkts	6 Pkts	36 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)