APRS Track Direct

My position About ☰

reset

LU5MN-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU5MN-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1754541883	11 Pkt	-38 dBm	12.47 V
1754540870	11 Pkt	-38 dBm	12.47 V
1754539855	13 Pkt	-38 dBm	12.47 V
1754538842	10 Pkt	-38 dBm	12.47 V
1754537828	11 Pkt	-38 dBm	12.47 V
1754536814	14 Pkt	-38 dBm	12.47 V
1754535800	10 Pkt	-38 dBm	12.47 V
1754534787	13 Pkt	-38 dBm	12.47 V
1754533773	11 Pkt	-40 dBm	12.47 V
1754532759	10 Pkt	-39 dBm	12.47 V
1754531745	12 Pkt	-39 dBm	12.47 V
1754530731	12 Pkt	-39 dBm	12.47 V
1754529717	12 Pkt	-40 dBm	12.47 V
1754528703	11 Pkt	-40 dBm	12.47 V
1754527689	11 Pkt	-40 dBm	12.47 V
1754526675	11 Pkt	-40 dBm	12.47 V
1754525662	10 Pkt	-40 dBm	12.47 V
1754524647	11 Pkt	-40 dBm	12.47 V
1754523633	12 Pkt	-39 dBm	12.47 V
1754522619	10 Pkt	-38 dBm	12.47 V
1754521605	12 Pkt	-39 dBm	12.47 V
1754520591	12 Pkt	-38 dBm	12.47 V
1754519577	9 Pkt	-39 dBm	12.47 V
1754518563	13 Pkt	-48 dBm	12.47 V
1754517550	10 Pkt	-46 dBm	12.47 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)