APRS Track Direct

My position About ☰

reset

YO3JAZ-NC Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3JAZ-NC. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Power*	Load*	RSSI*	Vcc*
1836274756	21.5 C	0 W	7.2 %	-57 dBm	3.42 V
1836274396	21.5 C	0 W	7.2 %	-55 dBm	3.42 V
1836274366	21.5 C	0 W	7.2 %	-55 dBm	3.43 V
1836274036	21.5 C	0 W	7.6 %	-55 dBm	3.43 V
1774101202	13.5 C	640 W	7.6 %	-59 dBm	3.43 V
1774100842	13.5 C	640 W	7.6 %	-59 dBm	3.44 V
1774100482	13.5 C	700 W	7.2 %	-59 dBm	3.44 V
1774100122	13.5 C	700 W	7.6 %	-59 dBm	3.44 V
1774099762	13.5 C	860 W	7.6 %	-59 dBm	3.43 V
1774099402	13.5 C	940 W	7.6 %	-59 dBm	3.44 V
1774099042	13.5 C	1000 W	7.6 %	-60 dBm	3.44 V
1774098682	13.5 C	940 W	7.6 %	-60 dBm	3.44 V
1774098322	13.5 C	820 W	7.2 %	-60 dBm	3.44 V
1774097962	13.5 C	660 W	7.6 %	-60 dBm	3.44 V
1774097602	13.5 C	540 W	7.2 %	-60 dBm	3.44 V
1774097242	13.5 C	460 W	7.6 %	-60 dBm	3.44 V
1774096882	13.5 C	600 W	7.2 %	-60 dBm	3.44 V
1774096522	13.5 C	720 W	7.2 %	-60 dBm	3.44 V
1774096162	13.5 C	840 W	7.2 %	-60 dBm	3.44 V
1774095802	13.5 C	1120 W	7.2 %	-60 dBm	3.44 V
1774095442	13.5 C	1580 W	7.6 %	-59 dBm	3.44 V
1774095082	13.5 C	2700 W	7.2 %	-59 dBm	3.44 V
1774094722	13.5 C	2000 W	7.6 %	-60 dBm	3.44 V
1774094362	13.5 C	2100 W	7.2 %	-60 dBm	3.44 V
1774094002	13.5 C	1120 W	7.2 %	-59 dBm	3.44 V

*Used Equation Coefficients:

Temp: 0, 0.5, -25

Power: 0, 20, 0

Load: 0, 0.4, 0

RSSI: 0, -1, 0

Vcc: 0, 0.01, 2.5

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)