APRS Track Direct

My position About ☰

reset

YC1JEA-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC1JEA-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274838	0 Pkt	-56 dBm	21 V
1836274528	0 Pkt	-54 dBm	21 V
1836274398	0 Pkt	-56 dBm	21 V
1836274218	0 Pkt	-55 dBm	21 V
1836273908	0 Pkt	-54 dBm	21 V
1770138289	0 Pkt	-50 dBm	1.89 V
1770137979	0 Pkt	-50 dBm	1.87 V
1770137669	0 Pkt	-50 dBm	1.93 V
1770137359	0 Pkt	-50 dBm	1.89 V
1770137049	0 Pkt	-50 dBm	1.8 V
1770136739	0 Pkt	-48 dBm	1.83 V
1770136429	0 Pkt	-49 dBm	1.91 V
1770136119	0 Pkt	-47 dBm	1.83 V
1770135809	0 Pkt	-49 dBm	1.85 V
1770135499	0 Pkt	-49 dBm	1.83 V
1770135114	0 Pkt	-50 dBm	1.85 V
1770134804	0 Pkt	-49 dBm	1.85 V
1770134494	0 Pkt	-50 dBm	1.85 V
1770134184	0 Pkt	-50 dBm	1.83 V
1770133874	2 Pkt	-52 dBm	1.83 V
1770133564	1 Pkt	-53 dBm	1.85 V
1770133254	1 Pkt	-50 dBm	1.87 V
1770132944	1 Pkt	-52 dBm	1.83 V
1770132634	0 Pkt	-51 dBm	1.78 V
1770132324	0 Pkt	-50 dBm	1.85 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)