APRS Track Direct

My position About ☰

reset

TA5ERJ Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA5ERJ. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1754007566	6 Pkt	-75 dBm	13.6 V
1754007265	17 Pkt	-74 dBm	13.95 V
1754006922	15 Pkt	-75 dBm	13.95 V
1754006579	6 Pkt	-75 dBm	13.95 V
1754006182	20 Pkt	-75 dBm	13.99 V
1754005837	6 Pkt	-75 dBm	13.95 V
1754005555	16 Pkt	-75 dBm	13.95 V
1754005204	19 Pkt	-75 dBm	13.97 V
1754004858	8 Pkt	-75 dBm	13.99 V
1754004556	25 Pkt	-74 dBm	13.99 V
1754004204	11 Pkt	-74 dBm	13.99 V
1754003868	5 Pkt	-74 dBm	13.97 V
1754003583	18 Pkt	-74 dBm	13.95 V
1754003237	16 Pkt	-74 dBm	13.99 V
1754002893	13 Pkt	-77 dBm	13.58 V
1754002493	19 Pkt	-75 dBm	13.95 V
1754002145	8 Pkt	-75 dBm	13.62 V
1754001859	18 Pkt	-75 dBm	13.97 V
1754001514	19 Pkt	-75 dBm	13.97 V
1754001168	10 Pkt	-75 dBm	13.99 V
1754000835	24 Pkt	-74 dBm	13.97 V
1754000480	10 Pkt	-76 dBm	13.97 V
1754000137	24 Pkt	-75 dBm	13.99 V
1753999785	20 Pkt	-74 dBm	13.97 V
1753999437	9 Pkt	-75 dBm	13.56 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)