APRS Track Direct

My position About ☰

reset

TA5BLT-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA5BLT-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	RSSI*	Voltage*
1754179030	10 Pkt	-72 dBm	0.06 V
1754175407	29 Pkt	-72 dBm	0.06 V
1754171783	54 Pkt	-71 dBm	0.06 V
1754168157	9 Pkt	-70 dBm	0.06 V
1754164534	10 Pkt	-71 dBm	0.06 V
1754160911	10 Pkt	-70 dBm	0.06 V
1754157289	20 Pkt	-70 dBm	0.06 V
1754153665	13 Pkt	-69 dBm	0.06 V
1754150043	27 Pkt	-70 dBm	0.06 V
1754146419	22 Pkt	-69 dBm	0.06 V
1754142796	86 Pkt	-69 dBm	0.06 V
1754139169	58 Pkt	-69 dBm	0.06 V
1754135542	42 Pkt	-70 dBm	0.06 V
1754131917	10 Pkt	-70 dBm	0.06 V
1754128294	8 Pkt	-72 dBm	0.06 V
1754124672	11 Pkt	-69 dBm	0.06 V
1754121049	15 Pkt	-68 dBm	0.06 V
1754117426	27 Pkt	-68 dBm	0.06 V
1754113802	10 Pkt	-68 dBm	0.06 V
1754110180	8 Pkt	-72 dBm	0.06 V
1754106557	9 Pkt	-67 dBm	0.06 V
1754102934	10 Pkt	-69 dBm	0.06 V
1754099312	9 Pkt	-68 dBm	0.06 V
1754095689	10 Pkt	-71 dBm	0.06 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)