APRS Track Direct

My position About ☰

reset

YM5KKE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM5KKE-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274585	0 Pkt	-68 dBm	12.18 V
1762328771	1 Pkt	-72 dBm	12.18 V
1762327954	1 Pkt	-75 dBm	12.2 V
1762327135	1 Pkt	-72 dBm	12.18 V
1762326317	1 Pkt	-71 dBm	12.2 V
1762325497	2 Pkt	-71 dBm	12.2 V
1762324678	1 Pkt	-71 dBm	12.18 V
1762323859	1 Pkt	-70 dBm	12.18 V
1762323041	1 Pkt	-81 dBm	12.2 V
1762322222	1 Pkt	-82 dBm	12.18 V
1762321404	1 Pkt	-82 dBm	12.18 V
1762320585	2 Pkt	-85 dBm	12.2 V
1762319766	1 Pkt	-85 dBm	12.18 V
1762318948	1 Pkt	-83 dBm	12.18 V
1762318129	1 Pkt	-83 dBm	12.2 V
1762317310	0 Pkt	-79 dBm	12.18 V
1762316409	3 Pkt	-82 dBm	12.18 V
1762315590	2 Pkt	-81 dBm	12.18 V
1762314772	1 Pkt	-82 dBm	12.2 V
1762313953	2 Pkt	-82 dBm	12.2 V
1762313134	1 Pkt	-80 dBm	12.2 V
1762312316	1 Pkt	-81 dBm	12.18 V
1762311497	1 Pkt	-79 dBm	12.2 V
1762310678	2 Pkt	-81 dBm	12.18 V
1762309860	2 Pkt	-81 dBm	12.18 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)