APRS Track Direct

My position About ☰

reset

HS4LFU-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS4LFU-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1750096860	0 Pkt	-72 dBm	13.84 V
1750095937	0 Pkt	-71 dBm	13.86 V
1750095012	0 Pkt	-71 dBm	13.88 V
1750094088	0 Pkt	-68 dBm	13.86 V
1750093164	0 Pkt	-71 dBm	13.86 V
1750092239	0 Pkt	-71 dBm	13.86 V
1750091315	1 Pkt	-71 dBm	13.86 V
1750090390	0 Pkt	-70 dBm	13.88 V
1750089466	0 Pkt	-74 dBm	13.86 V
1750088542	0 Pkt	-74 dBm	13.86 V
1750087618	4 Pkt	-72 dBm	13.86 V
1750086693	1 Pkt	-76 dBm	13.88 V
1750085768	0 Pkt	-77 dBm	13.88 V
1750084844	0 Pkt	-77 dBm	13.86 V
1750083920	0 Pkt	-75 dBm	13.86 V
1750082996	0 Pkt	-74 dBm	13.86 V
1750082071	0 Pkt	-73 dBm	13.86 V
1750081147	0 Pkt	-75 dBm	13.86 V
1750080223	0 Pkt	-70 dBm	13.86 V
1750079299	0 Pkt	-76 dBm	13.86 V
1750078375	2 Pkt	-75 dBm	13.88 V
1750077450	0 Pkt	-72 dBm	13.86 V
1750076526	12 Pkt	-70 dBm	13.88 V
1750075601	0 Pkt	-73 dBm	13.88 V
1750074677	0 Pkt	-73 dBm	13.97 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)