APRS Track Direct

My position About ☰

reset

EA2URD-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EA2URD-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx1h*	Eff1h*
1836274446	14.03 Volt	80 Pkt	51 Pcnt
1770199466	14.1 Volt	80 Pkt	84 Pcnt
1770197784	14.03 Volt	80 Pkt	82 Pcnt
1770196104	14.03 Volt	90 Pkt	79 Pcnt
1770194421	14.1 Volt	90 Pkt	81 Pcnt
1770191059	14.03 Volt	90 Pkt	79 Pcnt
1770187695	14.03 Volt	80 Pkt	70 Pcnt
1770186013	14.1 Volt	100 Pkt	65 Pcnt
1770184332	14.18 Volt	110 Pkt	65 Pcnt
1770182650	14.03 Volt	110 Pkt	64 Pcnt
1770180969	14.03 Volt	120 Pkt	62 Pcnt
1770179290	14.03 Volt	120 Pkt	65 Pcnt
1770177604	14.1 Volt	110 Pkt	70 Pcnt
1770175924	14.03 Volt	100 Pkt	66 Pcnt
1770174241	14.1 Volt	90 Pkt	64 Pcnt
1770172561	14.18 Volt	100 Pkt	60 Pcnt
1770170879	14.18 Volt	110 Pkt	57 Pcnt
1770169198	14.03 Volt	100 Pkt	60 Pcnt
1770167516	14.1 Volt	80 Pkt	58 Pcnt
1770165834	14.1 Volt	100 Pkt	59 Pcnt
1770164153	14.1 Volt	90 Pkt	54 Pcnt
1770162471	14.03 Volt	100 Pkt	53 Pcnt
1770160789	14.18 Volt	100 Pkt	56 Pcnt
1770159108	14.03 Volt	90 Pkt	72 Pcnt
1770157426	14.1 Volt	90 Pkt	97 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)