APRS Track Direct

My position About ☰

reset

KN6PTX-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KN6PTX-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RFIn*	Temp*	V1*	V2*
1791745590	67 Pkts	19 C	0 V	0 V
1791744990	68 Pkts	18 C	0 V	0.1 V
1791744390	61 Pkts	18 C	0 V	0.1 V
1791743790	65 Pkts	19 C	0 V	0 V
1791743190	70 Pkts	17 C	0 V	0 V
1791742590	72 Pkts	17 C	0.1 V	0 V
1791741990	75 Pkts	17 C	0.1 V	0 V
1791741390	57 Pkts	17 C	0.2 V	0.1 V
1791740790	43 Pkts	17 C	0 V	0.1 V
1791740190	55 Pkts	17 C	0 V	0 V
1791739590	54 Pkts	17 C	0 V	0 V
1791738990	63 Pkts	17 C	0 V	0 V
1791738390	66 Pkts	17 C	0 V	0 V
1791737790	44 Pkts	17 C	0 V	0 V
1791737190	59 Pkts	17 C	0 V	0 V
1791736590	51 Pkts	16 C	0.1 V	0 V
1791735990	39 Pkts	17 C	0 V	0 V
1791735390	42 Pkts	16 C	0 V	0 V
1791734789	53 Pkts	16 C	0 V	0 V
1791734189	35 Pkts	16 C	0 V	0 V
1791733589	49 Pkts	16 C	0 V	0 V
1791732989	49 Pkts	15 C	0 V	0.1 V
1791732389	32 Pkts	15 C	0 V	0.1 V
1791731789	53 Pkts	15 C	0 V	0 V
1791731189	50 Pkts	15 C	0 V	0.2 V

*Used Equation Coefficients:

RFIn: 0, 1, 0

Temp: 0, 1, 0

V1: 0, 0.1, 0

V2: 0, 0.1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)